樹脂吸附式空氣干燥機

◆廠品性能 Product features

※存在相對穩定一直的吸氣的壓力和露點

1.吸附物塔之非常與孔徑經科學試驗最終精密鑄造計算出，塔床壓力差小，絕對了縮短氣休干澡劑5秒的接受耗時，達到機器設備氣的露點規范要求。

2.30％的粗糙劑裕量，代替補償費粗糙劑的理所當然退化，以保證粗糙。

3.大型的對外擴散器，有效確保熱空氣一致經過干熱劑層，祛除溝流物理現象。

※降解氣量材料耗費小于等于14％

1.有遠見的機筒規劃，導出100％的吸附劑糖份，永久保存的糖份適用加入回收利用時間段的回收利用氣溫暖，增長儀器的解吸特性，使人回收利用更徹底解決。

2.變干和重復利用采用了返向對流傳熱計劃，濕熱空氣走過干的吸附性劑實效果較好的。重復利用氣外貿出口含濕量的控制在亞過飽和狀況，使消音器及排氣管路通道無冷凝水之慮。

3.可依照干熱機的進行短路電流業務需求上下調整可可二次利用氣水量，抓好可可二次利用暖濕氣流維持不穩，可可二次利用壓低至臨界值。

※干澀劑食用保修期長

1.適于的機筒厚度，使氣體完成潮濕劑層的風速和準確時間保持著好的形態，積極更好地發揮潮濕劑的的性能。

2.恰當的控制系統配備，在暖濕熱空氣來到機筒前，經除油操作盡快清理掉暖濕熱空氣中內嘴油物與重廢棄物物，逃避吹干劑層受廢棄物。

※生產設備適用了有意思高品質智能及汽動閥和信得過的全電子無線可程序編寫序調整器，電腦網頁十分友好，自動的間隔顯現雙塔工作狀況，嵌套循環周期時間場所可編，出貨設置10min。閘閥生存期歷時50萬次動作圖片。

※筒身內側壁作冷鍍鋅鐵皮防潮治療，10年不生繡。

※動作圖片準確性、效能平衡、進行操作非常簡單，裝設無須基礎理論。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆最主要的技術性能 Main technical parameters